Page 17 - Tools
P. 17
Flywheel Tool
Flywheel Truing Hammer
is a three pound lead/steel
that lasts longer than a lead
hammer and is still soft
enough so that it will not
mar flywheels.
VT No. 16-1020
16-1839
16-1354
Factory Type Crank Truing Machine features cast Crank Assembly Removal Tool is used to press
iron construction. Designed to true stock style fly- flywheels from cases, press cases apart and break
wheels. 10” swing right side, 6” swing left side, 18” sealant bond, for 1955-up Big Twin, by Jims.
maximum center to center. Weighs over 80 pounds. VT No. 16-1839 1955-05
VT No. 16-1354 2006-17
Shipped truck only. Order 16-0071 roller stanchions
Flywheel Truing Tool to fine tune flywheel assemblies
separately. For fork tubes straightness check roller
when truing. This tool features both a flywheel expand-
stanchions. er, and contractor in one easy to use package. Use on
VT No. Item all tapered shaft flywheel assemblies.
16-0586 Machine VT No. 16-0325
16-0071 Roller Stanchions
16-1703 Hand Wheel 1930-54 Big Twin Flywheel End
Sprocket Shaft/Flywheel Play Gauge.
Holder used to hold flywheel VT No. 16-0131 Flywheel Nut Sockets feature a low profile of 1” tall
assembly in vise with or without to give 100% nut contact, machined flat at nut receiv-
left case attached. Can also be ing end to eliminate rounding off the nut, by Jims.
used to check case clearance VT No. Nut OEM Fits Drive
on stroker flywheels. Use on all Crank
TC-88, 2006-17 FXD, 2007-16 16-1809 23966-54A 1954-81 Big Twin 1/2”
FLT and 2007-17 FXST. 16-1810 23969-83 1983-up Big Twin 1/2”
VT No. 16-0326 16-1813 23901-81 1981-up XL 1/2”
Jims Flywheel 16-2753 16-1203 Sprocket
Runout Inspection 16-1812 24017-80 1972-up Big Twin 3/4”
Gauge allows engine Jims Flywheel Locking and Decommissioned Tool Flywheel Spreader Tool
builder to check fly- locks the flywheel in place making service procedures spreads wheels while truing
wheel runout of the easier. This tool is very visible and useful to designate for Big Twins and XL’s.
pinion shaft while a bike as decommissioned. The bike will not start and VT No. 16-0517
assembled in engine clutch must be engaged in order to move bike when
case. Also allows the checking of gear lash on gear this tool is installed. Use on all Twin Cams 1999-up
driven cams on Twin Cam engines. Gauge fits 1970- and 2017-up M-8 models.
84 FL, 1971-84 FX, 1984-up FXST, 1986-up FLST, VT No. Fits
1991-up FXD, 1979-up FLT, 1982-94 FXR. 16-2753 Twin Cam
VT No. 16-0383 16-1203 M-8
Balance Tool
Balancer Shaft Removal Tool Balancing Shaft and Bearing Outer Balancer Bearing Installer
designed to remove both front Installer Tool designed to align and Remover Tool removes and
and rear counter-balancer shaft and safely install a new balancer installs the outboard balancer
bearing assembly, from the left bearing and counter balancer shaft bearing on the 96” and 110” “B”
engine case on the 96” and into the Twin Cam 96” or 110” “B” Softail engines 2000-17 chain guide
110” Beta engines, 2007-17. Softail engine case 2000-17. For support plate.
VT No. 16-1374 removal of balancer shaft from the VT No. 16-1376
Balancer Shaft Bearing engine case use Jims tool No. 960. Balancer Shaft Retention Pin use this
Service Tool use to remove VT No. 16-1377 tool to secure the engine balancers on
and install bearing fits 2000- Jims Balancer Scissor Gear Twin Cam engines when servicing fly-
17 Twin Cam Engines. Alignment Screw holds the wheel assembly. This tool locks into the
VT No. 16-1915 two halves of the spring bal- balancers sprocket pin holes to prevent
ancer gear in alignment before the balancer from turning out of sync with
removal for easy installation. flywheel. Use on 2000-17.
Jims Beta Engine Use on 2017-up M-8 engines. VT No. 16-1163
Hydraulic Balancer VT No. 16-1181
Retainer Tool use these Jims Outer Balancer
retainers to hold the 16-5832 Bearing Installer and
hydraulic tensioners in Remover Tool. This tool
place when repairing removes and installs the
all Beta engines. The outboard balancer bearing
hydraulic tensioners are on 96” and 110” “B” Softail
used to keep constant chain tension on the counter Jims M-8 Balancer Bearing Remover Tool is for engines 2007-17. TOOLS
use on 2017-up FLT and 2018-up FXST models. The
balancer system. Without the use of these retaining M-8 engine design incorporates balancers to reduce VT No. 16-0324
tools you will not be able to remove or install the engine vibration. This tool can remove the balancer
balancing system. Use on all Beta Twin Cam engines
2000-17. bearings both Touring and Softail models without
damage to the crankcase.
VT No. 16-1858 VT No. 16-5832
1275
Flywheel Truing Hammer
is a three pound lead/steel
that lasts longer than a lead
hammer and is still soft
enough so that it will not
mar flywheels.
VT No. 16-1020
16-1839
16-1354
Factory Type Crank Truing Machine features cast Crank Assembly Removal Tool is used to press
iron construction. Designed to true stock style fly- flywheels from cases, press cases apart and break
wheels. 10” swing right side, 6” swing left side, 18” sealant bond, for 1955-up Big Twin, by Jims.
maximum center to center. Weighs over 80 pounds. VT No. 16-1839 1955-05
VT No. 16-1354 2006-17
Shipped truck only. Order 16-0071 roller stanchions
Flywheel Truing Tool to fine tune flywheel assemblies
separately. For fork tubes straightness check roller
when truing. This tool features both a flywheel expand-
stanchions. er, and contractor in one easy to use package. Use on
VT No. Item all tapered shaft flywheel assemblies.
16-0586 Machine VT No. 16-0325
16-0071 Roller Stanchions
16-1703 Hand Wheel 1930-54 Big Twin Flywheel End
Sprocket Shaft/Flywheel Play Gauge.
Holder used to hold flywheel VT No. 16-0131 Flywheel Nut Sockets feature a low profile of 1” tall
assembly in vise with or without to give 100% nut contact, machined flat at nut receiv-
left case attached. Can also be ing end to eliminate rounding off the nut, by Jims.
used to check case clearance VT No. Nut OEM Fits Drive
on stroker flywheels. Use on all Crank
TC-88, 2006-17 FXD, 2007-16 16-1809 23966-54A 1954-81 Big Twin 1/2”
FLT and 2007-17 FXST. 16-1810 23969-83 1983-up Big Twin 1/2”
VT No. 16-0326 16-1813 23901-81 1981-up XL 1/2”
Jims Flywheel 16-2753 16-1203 Sprocket
Runout Inspection 16-1812 24017-80 1972-up Big Twin 3/4”
Gauge allows engine Jims Flywheel Locking and Decommissioned Tool Flywheel Spreader Tool
builder to check fly- locks the flywheel in place making service procedures spreads wheels while truing
wheel runout of the easier. This tool is very visible and useful to designate for Big Twins and XL’s.
pinion shaft while a bike as decommissioned. The bike will not start and VT No. 16-0517
assembled in engine clutch must be engaged in order to move bike when
case. Also allows the checking of gear lash on gear this tool is installed. Use on all Twin Cams 1999-up
driven cams on Twin Cam engines. Gauge fits 1970- and 2017-up M-8 models.
84 FL, 1971-84 FX, 1984-up FXST, 1986-up FLST, VT No. Fits
1991-up FXD, 1979-up FLT, 1982-94 FXR. 16-2753 Twin Cam
VT No. 16-0383 16-1203 M-8
Balance Tool
Balancer Shaft Removal Tool Balancing Shaft and Bearing Outer Balancer Bearing Installer
designed to remove both front Installer Tool designed to align and Remover Tool removes and
and rear counter-balancer shaft and safely install a new balancer installs the outboard balancer
bearing assembly, from the left bearing and counter balancer shaft bearing on the 96” and 110” “B”
engine case on the 96” and into the Twin Cam 96” or 110” “B” Softail engines 2000-17 chain guide
110” Beta engines, 2007-17. Softail engine case 2000-17. For support plate.
VT No. 16-1374 removal of balancer shaft from the VT No. 16-1376
Balancer Shaft Bearing engine case use Jims tool No. 960. Balancer Shaft Retention Pin use this
Service Tool use to remove VT No. 16-1377 tool to secure the engine balancers on
and install bearing fits 2000- Jims Balancer Scissor Gear Twin Cam engines when servicing fly-
17 Twin Cam Engines. Alignment Screw holds the wheel assembly. This tool locks into the
VT No. 16-1915 two halves of the spring bal- balancers sprocket pin holes to prevent
ancer gear in alignment before the balancer from turning out of sync with
removal for easy installation. flywheel. Use on 2000-17.
Jims Beta Engine Use on 2017-up M-8 engines. VT No. 16-1163
Hydraulic Balancer VT No. 16-1181
Retainer Tool use these Jims Outer Balancer
retainers to hold the 16-5832 Bearing Installer and
hydraulic tensioners in Remover Tool. This tool
place when repairing removes and installs the
all Beta engines. The outboard balancer bearing
hydraulic tensioners are on 96” and 110” “B” Softail
used to keep constant chain tension on the counter Jims M-8 Balancer Bearing Remover Tool is for engines 2007-17. TOOLS
use on 2017-up FLT and 2018-up FXST models. The
balancer system. Without the use of these retaining M-8 engine design incorporates balancers to reduce VT No. 16-0324
tools you will not be able to remove or install the engine vibration. This tool can remove the balancer
balancing system. Use on all Beta Twin Cam engines
2000-17. bearings both Touring and Softail models without
damage to the crankcase.
VT No. 16-1858 VT No. 16-5832
1275
