Page 30 - Tools
P. 30
5 & 6 Speed Transmission Tool
Jims Main Drive Gear Case Seal Installer ensures
Jims M-8 Countershaft 1st Scissor Gear Align- correct alignment and installs seal to the correct depth
ment Tool ensures that the scissor gear teeth mesh without damaging seal. Fits 1986-2006 FLST, FXST, Jims Main Drive Gear Installer Tool. This tool will
correctly with the mainshaft 1st fear. For M-8 models. 1991-2005 FXD, 1985-2005 FLT. hold the main drive gear square to its bearing bore
*Note: it is installed before the scissor gear is re- VT No. 16-1028 for proper main drive gear installation. Use on 2006-
moved to maintain alignment of the gear halves under 17 Dynaglide and 2007-up FXST-FLT models.
spring pressure. VT No. 16-1190 16-0994 VT No. 16-1350
Jims Right Side Drive Transmission
Trap Door Puller Tool. Removes access
door on all right side drive transmissions.
VT No. 16-1356
Jims 5-Speed Transmission Main Drive Gear
Tool. Use 16-0994 to remove and install main drive 16-0756
5-Speed Main Drive Gear Seal Installer gear and install main bearing. Can be used without
Sets seal to proper depth with transmis- removing transmission case. Use on all 5 or 6-Speed
sion assembled. By Jims. VT No. 16-0664 1980-up Big Twins.
VT No. 16-0994
Main Drive Gear Seal Installer allows instal- 16-0731
lation of main drive gear oil seal on assem-
Countershaft Support Plate Tool bled transmission to proper depth. The pro-
fits 1991-up 5-speed Sportster. tective sleeve included is used for protecting
VT No. 16-1756 inner bearings of main drive for installation.
For 2006-up FXD and 2007-up FLST.
VT No. 16-1363
16-1645 16-0672
16-1883
Jims Transmission Countershaft Bearing Tool 16-0877 5-Speed Transmission Door Remover and Installer
will install and remove the closed end countershaft removes and replaces the door bearings Saves time
bearing on 5 and 6 speed Big Twin transmissions Big Twin Mainshaft Primary Bearing Race as the complete transmission does not have to be
without using a press or tapping with a transmission Remover and Installer for use on all 1984-up Big dismounted allowing the mainshaft and countershaft
shaft. Fits 1984-up FXST, 1986-up FLST, 1984-94 Twins, replaces 34902. clusters to remain in place for use when installing
FXR,1999-up FLT. VT No. 16-1883 VT No. Brand 5-Speed kicker kit.
Item/Brand
VT No.
16-1645 Sifton 16-0756 V-Twin Door Remover and Installer
16-0877 Jims 16-0731 Jims Installer Only
Replacement Parts for Above Tools. 16-0672 Bearing Remover/Installer
VT No. Item
16-0189 Puller Plate
16-0183 Pusher Tube
Cruise Drive 6-Speed Maindrive Gear Remover
Tool removes the main drive gear from the main bear- Cruise Drive 6-Speed Trap Door Bearing Remover/
ing correctly while in the transmission case. This elim-
inates the need of an arbor press and the risk of case Installer will accurately install a lubed ball bearing
into the transmission trap door. Also removes bearing
damage. For use on all Twin Cam 6-Speed Cruise
Drive models and all 2006 Dynaglide and all 2007 to Cruise Drive 6-Speed Maindrive Gear and Bearing without error and can be performed on a work bench,
present Twin Cam models. Remover/Installer Kit for servicing the main drive no need for an arbor press. Use on all Twin Cam
6-Speed cruise drive models, 2006 Dynaglide and all
VT No. 16-2130 gear or the main bearing on the latest 6-Speed trans-
mission. This precision tool removes or installs both 2007-up Twin Cam models.
parts correctly without damaging the case. Use on VT No. 16-2132
all Twin Cam 6-Speed Cruise Drive models, 2006
Dynaglide and all 2007-up Twin Cam models.
VT No. 16-2131
Speedometer Sending Unit Wrench features a short-
ened ³⁄₁₆” ball end hex bit for removal or installation of Jims Transmission Assembly Vise Stand assists in
hex screw used on all Big Twin models. Equipped with the assembly of transmission gears and shafts. This
electronic sending units. tool holds the shafts in perfect alignment while protect-
Jims M-8 Shifter Mechanism Sleeve Remover and VT No. 16-6738 ing them from damage. Use on all 2006-up 6-speed
Installer is for removing and installing the shifter transmissions.
mechanism sleeve in M8 transmissions. The sleeve VT No. 16-1029
can be removed and installed correctly without disas-
sembling the transmission.
VT No. 16-1191
1288
Jims Main Drive Gear Case Seal Installer ensures
Jims M-8 Countershaft 1st Scissor Gear Align- correct alignment and installs seal to the correct depth
ment Tool ensures that the scissor gear teeth mesh without damaging seal. Fits 1986-2006 FLST, FXST, Jims Main Drive Gear Installer Tool. This tool will
correctly with the mainshaft 1st fear. For M-8 models. 1991-2005 FXD, 1985-2005 FLT. hold the main drive gear square to its bearing bore
*Note: it is installed before the scissor gear is re- VT No. 16-1028 for proper main drive gear installation. Use on 2006-
moved to maintain alignment of the gear halves under 17 Dynaglide and 2007-up FXST-FLT models.
spring pressure. VT No. 16-1190 16-0994 VT No. 16-1350
Jims Right Side Drive Transmission
Trap Door Puller Tool. Removes access
door on all right side drive transmissions.
VT No. 16-1356
Jims 5-Speed Transmission Main Drive Gear
Tool. Use 16-0994 to remove and install main drive 16-0756
5-Speed Main Drive Gear Seal Installer gear and install main bearing. Can be used without
Sets seal to proper depth with transmis- removing transmission case. Use on all 5 or 6-Speed
sion assembled. By Jims. VT No. 16-0664 1980-up Big Twins.
VT No. 16-0994
Main Drive Gear Seal Installer allows instal- 16-0731
lation of main drive gear oil seal on assem-
Countershaft Support Plate Tool bled transmission to proper depth. The pro-
fits 1991-up 5-speed Sportster. tective sleeve included is used for protecting
VT No. 16-1756 inner bearings of main drive for installation.
For 2006-up FXD and 2007-up FLST.
VT No. 16-1363
16-1645 16-0672
16-1883
Jims Transmission Countershaft Bearing Tool 16-0877 5-Speed Transmission Door Remover and Installer
will install and remove the closed end countershaft removes and replaces the door bearings Saves time
bearing on 5 and 6 speed Big Twin transmissions Big Twin Mainshaft Primary Bearing Race as the complete transmission does not have to be
without using a press or tapping with a transmission Remover and Installer for use on all 1984-up Big dismounted allowing the mainshaft and countershaft
shaft. Fits 1984-up FXST, 1986-up FLST, 1984-94 Twins, replaces 34902. clusters to remain in place for use when installing
FXR,1999-up FLT. VT No. 16-1883 VT No. Brand 5-Speed kicker kit.
Item/Brand
VT No.
16-1645 Sifton 16-0756 V-Twin Door Remover and Installer
16-0877 Jims 16-0731 Jims Installer Only
Replacement Parts for Above Tools. 16-0672 Bearing Remover/Installer
VT No. Item
16-0189 Puller Plate
16-0183 Pusher Tube
Cruise Drive 6-Speed Maindrive Gear Remover
Tool removes the main drive gear from the main bear- Cruise Drive 6-Speed Trap Door Bearing Remover/
ing correctly while in the transmission case. This elim-
inates the need of an arbor press and the risk of case Installer will accurately install a lubed ball bearing
into the transmission trap door. Also removes bearing
damage. For use on all Twin Cam 6-Speed Cruise
Drive models and all 2006 Dynaglide and all 2007 to Cruise Drive 6-Speed Maindrive Gear and Bearing without error and can be performed on a work bench,
present Twin Cam models. Remover/Installer Kit for servicing the main drive no need for an arbor press. Use on all Twin Cam
6-Speed cruise drive models, 2006 Dynaglide and all
VT No. 16-2130 gear or the main bearing on the latest 6-Speed trans-
mission. This precision tool removes or installs both 2007-up Twin Cam models.
parts correctly without damaging the case. Use on VT No. 16-2132
all Twin Cam 6-Speed Cruise Drive models, 2006
Dynaglide and all 2007-up Twin Cam models.
VT No. 16-2131
Speedometer Sending Unit Wrench features a short-
ened ³⁄₁₆” ball end hex bit for removal or installation of Jims Transmission Assembly Vise Stand assists in
hex screw used on all Big Twin models. Equipped with the assembly of transmission gears and shafts. This
electronic sending units. tool holds the shafts in perfect alignment while protect-
Jims M-8 Shifter Mechanism Sleeve Remover and VT No. 16-6738 ing them from damage. Use on all 2006-up 6-speed
Installer is for removing and installing the shifter transmissions.
mechanism sleeve in M8 transmissions. The sleeve VT No. 16-1029
can be removed and installed correctly without disas-
sembling the transmission.
VT No. 16-1191
1288
